Reasonable price What Is A Reefer Trailer - aftermarket adas Fatigue driving camera DB-A502 – Dragon Bridge

Instruction Book of

DB-A502 

Forward Vision Early Warning System

I. Product Introduction

Roadragon DB-A502 is a product of forward vision early warning system based on machine vision, which can provide a driver with Forward Collision Warning (FCW), Urban Forward Collision Warning (UFCW), Virtual Bumpers (VB), Headway Monitoring and Warning (HMW), Lane Departure Warning (LDW), and other driving security alerting functions. This product performs real-time monitoring of the vehicle traveling state by means of a front-facing camera and an image processor and gives an alarm or alert in time in case of a dangerous state, so as to avoid the occurrence of traffic accidents.

II. Product Overview

Product Front View Product Side View

Ⅲ.First Use

1. Installation

When DB-A502 is installed, the camera should be fixed onto the central location of the front windscreen, that is, a left or right position within a range of 10 cm from the central axis of the vehicle will be allowed and a position closer to the center will be more desired.

Note: the camera cannot be blocked by windscreen wipers; for a vehicle with its engine projecting from the front windscreen, the installation location should be appropriately raised in order to ensure that the camera is not blocked by the front projection.

The power line, ACC signal line, turning signal line, and brake signal line are well connected. (There is no need to connect the signal line when a variety of signal lines are acquired through communications with other devices.)

 Instruction Book Of DB-A502

2. Parameter Setting

Pre-download specific calibration software DB-A502 APP for mobile terminal of the ADAS product from ROADRAGON Vision.

Connect your phone to DB-A502 wifi hotspot named xCamera with the initial password of 12345678.

Open the software and set parameters according to the steps guided by the software until the setting is completed.

For detailed operating instructions, please refer to Annex 1: DB-A502 APP Instruction Manual.

IV. Function Description

1. Forward Collision Warning (FCW)

When the speed of a vehicle exceeds 30 Km/h, the FCW module will begin to work. When the vehicle has a larger speed than a vehicle in front and is likely to collide with it,DB-A502 will send out a warning at most 3 seconds in advance and the warning sound will be “beep, beep, beep~”.

2. Urban Forward Collision Warning (UFCW)

When a vehicle runs at a speed of less than 30 Km/h and moves close to another vehicle in front, the device will send out a sharp warning sound “beep, beep, beep” before a possibly imminent collision.

3. Virtual Bumpers (VB)

The device will send out a warning sound “beep, beep, beep” before a collision with the vehicle in front possibly resulting from a very low speed (car sliding).

4. Headway Monitoring and Warning (HMW)

When the speed of the vehicle exceeds 30 Km/h, the HMW module will begin to work. When the distance from the vehicle to another vehicle in front reaches the set Level 1 minimum distance, the device will send out a warning to remind the driver of the vehicle in front and the warning sound will be “beep~”; and when the distance from the vehicle to another vehicle in front reaches the Level 2 minimum distance, the device will send out a warning sound “beep, beep~” to remind the driver of a too close distance and the warning sound will be repeated at an interval of 5s until a safe distance is restored.

Warning: No matter whether the device DB-A502 sends out a warning or not, you (the driver) will be solely responsible for keeping a safe distance from the vehicle in front.

5. Lane Departure Warning (LDW)

DB-A502 will start the LDW module when the vehicle speed is higher than 50 Km/h, and when the driver departs from the lane unintentionally, the device will send out a warning and the warning sound will be “ding~ding~”.

The LDW module will not send out a warning in the following cases:

the turn signal lamp or hazard flasher is turned on when changing the lane;

quick lane switching is performed;

the driver steps on the brake when changing the lane;

the driver changes the lane in an acceleration or a deceleration state;

lane lines are not marked or are not clear;

f. the speed is less than 50 Km/h;

under adverse weather conditions.

6.Driving Video Recording

DB-A502 can record 1080P HD videos and perform automatic cyclic recording every 3 minutes and store data into the high-speed class 10 SD card.

7.Emergency Lockout

When the vehicle encounters severe turbulence or collision during traveling,DB-A502 can immediately lock the current video and will not delete it from cyclic recording.

8. Driving Behavior Detection

The DB-A502 can detect the Rapidly Speeding-up, Hard Braking, and High-speed Turning of the vehicle through built-in sensors.

9. Video Output

DB-A502 supports video output in CVBS format, or support the PAL (default) or NTSC system for video recording by DVR.

10. Volume Adjustment

The volume can be lowered or increased by repeatedly pressing the button (-) or (+) on the side of the product, respectively; and the volume is at five levels of from 1 to 5.

11. Serial Port Communications

DB-A502 can support RS232 and can communicate with other devices to transmit vehicle information and various alarm information.

12. Signal Input and Output

DB-A502 has 3-way signal inputs which can be connected to the turn signal and brake signal.

13. Mobile APP Linkage

An Android Phone may install ROADRAGON APP in “Road-Defend” and may be connected to the WiFi hotspot of the device, and then real-time video viewing and requesting of videos under History on demand can be achieved.

 V. System Limitations

The DB-A502 system applies to asphalt roads with clearly marked lane lines.

 1. The DB-A502 system cannot “watch” road conditions instead of the driver. The driver should always be vigilant while driving, and drive based on road conditions observed or heard by himself or herself; 

1.Usage License

The software used in this product is proprietary to ROADRAGON. ROADRAGON only grants the

purchaser a non-exclusive license to use the software, and consumers shall not:

(a) Amend, modify, change or convert the software used in the product or provided along with the product from ROADRAGON, or create derivative works therefrom;

(b) Reverse assemble, decompile, disassemble or otherwise attempt to obtain source code for the software;

 (c)  Assign, sublicense, lease, rent, lend, transfer, disclose, or otherwise have access to such

software;

(d)  Remove property statements from the product or corresponding documents.

2.Limited Warranty

This product is warranted to the original purchaser of the product installed on the vehicle to be free of defects in materials and workmanship for a period of one year from the date of purchase (or in accordance with applicable law). If it is determined that the product offered by ROADRAGON Vision is defective in materials and workmanship, ROADRAGON Vision will be solely liable to provide repair or replacement (at its own option). ROADRAGON Vision will not be liable for any problems caused by installation. The following is not covered by warranty:

(a) Damages caused by misuse, negligence, improper installation or accident;

(b) Installation of the productDB-A502 onto an inapplicable vehicle;

(c) Any repair or alteration of this product performed by any third party other than ROADRAGON.

3.Disclaimer

This limited warranty is the only exclusive warranty for the product from ROADRAGON. Within the scope permitted by applicable law, ROADRAGON disclaims all warranties of any kind, either implied or express, including but not limited to the warranties of merchantability and fitness for a particular purpose. No representative, distributor, dealer or agent is authorized to make a statement, a warranty or an agreement on the productDB-A502 on behalf of ROADRAGON. Besides clear statements herein, ROADRAGON will not make any other statements or warranties. In any case, ROADRAGON will not be liable for special, collateral, indirect, punitive, incidental, consequential, or exemplary damages related to the productDB-A502 or resulting from the use thereof.

4.After Service

If the product has a problem, please refer to the following process:

1） Contact the distributor who sold you the product;

2） If this product was purchased directly from ROADRAGON, please contact ROADRAGON. Freight on all returned products must be prepaid. Each returned product must have a return authorization number and you can contact the customer service department to get this number.

Annex 1 “DB-A502” Parameter Configuration App Instruction Manual

Ⅰ.Software Installation

1.Call customer service telephone +86-21-55896781 to request the “DB-A502″ APP installation package.
2.Provide the following information for opening an account.Serial No.                  Information

1 Company Name

2 The region where the company is located, such as Nanjing, Jiangsu and Nanchang, Jiangxi.

3 Contact information:   name, telephone, email

Ⅱ.User Login

When login at the first time, the user will see the interface as shown in Figure 2-1, and after entering the account number and password and logging in, the user will see the interface as shown in Figure 2-2.

III. Vehicle Type Selection

Click “Vehicle Selection” and switch to the interface as shown in Figure 3-1, including such contents as the brand, series, Vehicle Type/Model Year/Components.

1. Select directly “confirm” if the database contains data of the corresponding vehicle type, as shown in fig. 3-2;

2. You will need to add a new brand or add data about vehicle type into the existing brand according to steps as follows if the database contains no data of the corresponding vehicle type.

A． Click the “Add” button in the upper right corner of Figure 2-1, pop-up Figure 2-3, and enter the relevant parameters (the picture is optional while other parameters are mandatory).

B． You can “submit for auditing” after entering the data, and inform our staff of data auditing.

C． You can check the submitted data in the menu of audit results, as shown in Figure 3-4; in case of “audit pass”, you can re-select from “Vehicle Selection” the data which just pass the auditing, as shown in Figure 3-2, and confirm completion of “Vehicle Selection”.