New Delivery for Track Your Container - best gps tracker for car Long Connection GPS Tracker MT008G – Dragon Bridge

GPS vehicle communication terminal

（GPS+GSM+SMS/GPRS）

V1.2.1017

Model：G-MT008G

1. Product accessories map：

Power cord                                                     Relay（optional） 

Microphone（optional）                           SOS Alarm button(optional)

Fixed magic stick

2. Product function：

1. Adopt UBXLO-7020 GPS module and 3G (HSDPA/WCDMA) communication module.
2. GPS+GSM base station dual mode location
3. Data communication: SMS/GPRS/HSDPA R5/WCDMA R99/EDGE/CSD (TCP/UDP)
4. Real-time query location
5. Chinese address query
6. Timed tracking
7. Pitch tracking
8. Mobile phone positioning
9. Built-in large capacity standby battery
10. Electronic fence
11. GPS blind area alarm
12. An electric alarm
13. Speeding alarm
14. Mileage report
15. Pronunciation monitoring (selection)
16. SOS emergency alarm (selection)
17. Remotely cutting off car oil / electricity (selection)

Specification parameter 

3. Appearance diagram

1. Installation instructions

4.1 Preparatory work before installation

4.1.1 Open the packing box, check whether the type of the equipment is correct, whether the accessories are complete or not, please contact your dealer.

4.1.2 SIM card selection, terminal need to insert a GSM SIM card, SIM card selection, please refer to the dealer’s opinion.

4.1.3 SIM card installation, on the left side of the terminal has a SIM card slot, open the SIM card seal ring, the SIM card metal face inserted into the SIM card slot (pay attention to SIM card do not reverse), insert in place can hear click sound, otherwise the SIM positive and reverse direction should be reinserted, the back cover back to seal the apron.

Be careful：

The terminal SIM card needs to open the GPRS function.

The terminal SIM card needs to open the caller display.

4.2 installation

The installation mode of the terminal is hidden installation. The hidden installation of terminal equipment is recommended by the professional institution designated by the distributor.

4.2.1 in order to avoid thieves’ destruction, the location of equipment should be hidden as far as possible.

4.2.2 avoid being placed with launch sources, such as reversing radar, burglar alarm and other vehicle communication equipment.

4.2.3 can be fixed with bandage or glued with wide sponge and strong double-sided adhesive.

The 4.2.4 equipment is equipped with GSM antenna and GPS antenna. When installing, it should ensure that it is upwards (skyward) and has no metal shielding shielding.

The front windshield is hidden beneath the plate.

The front dial dial (epidermis is non-metallic material) around the concealed place;

Underneath the rear windshield;

4.3 Definition of terminal outgoing line

Relay connection instructions

The connection method of the oil pump circuit breaker relay: the wire ends of the coil are fine white line (85) and the fine green line (86), the fine white line (85) is connected to the positive pole (+12V) of the automobile power supply, and the fine green line (86) is connected to the terminal relay control line.

The oil pipe of the controlled vehicle is connected with the oil pump, which is cut off the positive connection line of the oil pump. The oil pump is directly connected to the constant end of the relay (the green line 87A), and the other end is connected to the common end of the relay (the green line 30).

Note: the product is 12V relay. Suitable for vehicles equipped with 12V battery.

If the vehicle is equipped with 24V battery car, 24V relay should be selected separately.

1. Precautions for equipment wiring

Power, ACC, oil cut electric control line (4Pin)

The standard power supply for this equipment is 9V~80VDC. Please select the power line supplied by the original factory, the red line is the positive pole of the power supply, and the black line is the negative pole of the power supply. When installing the power negative pole, please choose a separate grounding or grounding, and do not connect with other ground wires.

2. terminal parameter setting

All the following function parameters set up the letter in the instruction format. All the symbols are English punctuation. All the instructions are sent back. The parameter instruction is set successfully. Otherwise, it needs to be reset. Sending the corresponding query command terminal will reply to the corresponding query content.

3.Log on to the global positioning service platform

Service platform landing site: www.dbgps.com