1.Main functional characteristics of the product：
1 ,built-in GPS module or Beidou module,
2, support 2G or 3G (WCDMA) network
3, the use of RFID electronic tag, support RFID card unlock function
4, the use of high strength plastic mold, lock body is not easy to destroy, passive failure will provide an alarm signal, can be anti fall, shock, waterproof, dust-proof.
5, high capacity battery, up to 15000MHA, can be connected to work for up to 7 days
6, built-in strong magnetic, can make the lock firmly adsorbed on the car body
7, with low power alarm function, when the electricity is less than a certain value, the indicator light will start
8, with buzzer prompt function, when the lock is not normally locked, the terminal will automatically issue beep alarm to remind the driver
9, terminal with alarm reminders, when sewing is illegally cut off when the terminal will take the initiative to send alarm
10, GPRS communication mode terminal, after each connection, automatically enter the GPS positioning mode, using TCP/IP and UDP protocol,
11, remote configuration of the relevant logistics lock information.
12, location information, switch status, electronic lock, instant information, etc..
13, monitoring center remote authority unlock, IC card unlock mode, handheld unlock mode, SMS unlock mode, etc.
14, monitoring center according to the pre-set location, range, vehicle overtime, route to regulate the logistics of walking routes, such as violations, real-time reporting, monitoring and so on.
2. Product appearance / technical parameter：
- Product parameters：
|
Hardware features |
|
|
Hardware architecture |
Use STM32 |
|
Communication module |
GPRS、WCDMA |
|
Technical specifications |
|
|
Operating Voltage |
3.6 V/DC |
|
Average operating current |
170 |
|
RFID |
S70 |
|
spare battery |
15000mAh continue working 7 days |
|
Dimensions |
335(with beam)mm*102mm*35mm |
|
Host weight |
1 KG |
|
Environmental characteristics |
|
|
Automotive EDM Interference Immunity |
Discharge voltage of 1kV ~ 2kV, discharge frequency of 20 times / s ~ 200 times / s |
|
Fast Transient Burst Impedance |
4KV, experimental grade IV |
|
Electrostatic discharge immunity |
Contact discharge 6KV, air discharge 8KV, experimental grade Ⅲ |
|
Conducted harassment limits |
Meet the requirements of Class B |
|
Radiation disturbance limits |
Meet the requirements of Class B |
|
Temperature characteristics |
Operating temperature -40 ℃ ~ +75 ℃ |
|
humidity |
5% to 95% non-condensing |
|
GPS performance |
|
|
Sensitivity |
－159dBm |
|
Positioning time |
Cold start less than 34 seconds; hot start less than 3.5 seconds; warm start less than 33 seconds, re-capture time 1.0 seconds |
|
positioning accuracy |
10m |
|
Speed accuracy |
0.1m/s |
|
GSM / GPRS performance |
|
|
frequency |
850/ 900/ 1800/ 1900 MHz |
|
Transmit power |
Class 4 (2W @ 850/ 900 MHz)Class 1(1W @ 1800/1900MHz) |
|
Operating temperature |
-40 °C to +85 °C |
|
data storage |
|
|
Blind sector cache |
Cache 2000 (point) location information |
2.Host LED status description：
1.Green LED — Indicates GPS signal status
| State | Definition |
| Flash (flash once every 1 second) | Searching for GPS signals. |
| Slow flash (every 5 seconds flash) | Has been targeted |
2.Red LED — indicates GSM status
| State | State |
| Flash (flash once every 1 second) | Flash (flash once every 1 second) |
| Slow flash (every 3 seconds flash) | Slow flash (every 3 seconds flash) |
| Frenzy (0.2 seconds flash 2S) | Frenzy (0.2 seconds flash 2S) |
3.Blue LED — indicates the charge status
| State | Definition |
| not bright | No charge or full charge |
| Always bright | The main power has been connected |
4.Orange LED — undervoltage indication status
| State | Definition |
| not bright | Power is normal but no power |
| Always bright | The machine is currently in an undervoltage condition |
3．Set the machine parameters:
After you have read the above description of the product, the product has been installed and the SIM card is installed. The following specific operation to start using.
Note: So the SMS command should be entered in English mode, the command error or format error will not reply.
1.Device IP address and Port
Send the message to the device number on the instruction format：
AS1234*F10#1,113.106.93.50,8011,1#
Reply to terminal parameters
IP:113.106.93.50,8011,1,cmnet,gprs,gprs,ID:31684086,M:6,GPS:A,9,CSQ:19,CGR:5,ACC:1,BAT:65%,VER:AT10-V1.0
Such as：
IP address:113.106.93.50 port:8011，TCP
Order“AS1234*F10#1,113.106.93.50,8011,1#”
The instruction is * AS *, “1234″ is the password, the initial default is 1234, “* F10 # 1″ means that this command is to set the machine’s IP instruction, 113.106.93.50 that the machine is connected to the server, 7001 for the port, 0 means the machine uses UDP to connect with the platform, if you want to use TCP to 1.
2.Query terminal status
Send SMS to device number, instruction format
AS1234STATE#
Reply terminal parameter
IP:113.106.93.50,8011,1,cmnet,gprs,gprs,ID:31684086,M:6,GPS:A,9,CSQ:19,CGR:5,ACC:1,BAT:65%,VER:AT10-V1.0
IP: 113.106.93.50 Represents the server address reported by the current machine，
Port: 7001 Represents the port of the current machine，0 means UDP Report，If it is 1 means TCP report
Cmnet,gprs,gprs：means current device APN
ID：31684086 means device ID number
GPS:A,9 means the positioning state of the current machine, V means no positioning，A means,9 mean 9 level accuracy
CSQ:19,Mobile information for the current machine
CGR：5 indicates the status of the card，
ACC：1 indicates the status of the lock, the 1 is the unlock, and the 0 is the lock
BAT：65% current lock capacity
VER: AT10-V1.0 Represents the version that is currently burned by the machine
M:6 That represents the current state of the machine, 6 online, 0 said 1 initialization, query CSQ, 2 registered network, 3 query the status of the CGREG, said the 4 registered APN, 5 said the connection to the server, 7 is disconnected from the network, said the 8 call, said 9 upgrade
3.SMS unlock
Send SMS commands “AS1234*F10#8,888888, #” to the number of terminal equipment, the contents of the “Open lock OK replied,” to this content said off terminal unlock success
The password can be unlocked remotely. For security, please consult the supplier to unlock the password.
4.Set the unlock reporting frequency
Send SMS instructions“AS1234*F10#G,300,600,#”Number to device，The terminal replies to
“accOn:300 accOff:600 rd:0 sp:0,0s stp:0 dr:0,0 idl:0 mv:0 time:+8 cq:0,0 geo:0 step:377 ack:0 msg:2568,56 sleep:0,0
”，The terminal has returned this content to indicate successful recovery
ACCon:Represents the lock off reporting interval
ACCoff:Represents the lock on reporting interval
Sleep Represents sleep time
5.Restore factory
Send SMS instructions“ASAX*%UPAS”Number to device，The terminal replies to“password:1234,OK”，The terminal has returned this content to indicate successful recovery
6.Restart terminal
Send SMS instructions“AS1234RSGS#”To the number of the device, the terminal replies to“GSM/Restart;OK”，The terminal has returned this content to indicate a successful restart
Attention：
- All the SMS edit in English mode, Chinese mode input will lead directly to delete, do not reply sms.
- All the messages are beginning to AS, to the end of #, format error will cause the application to not recognize.
- The 1234 machine factory default password, if the password is wrong, will cause the application to not reply SMS
