Fast delivery Gps Tracking Companies - gps tracking padlock GLL150 3G Device tracking navigation 3G Remote management – Dragon Bridge

Intelligent lock operation instructions

(V1.0)

1.Main pieces and accessories：

1. the logistics lock a host

2. a charger

3. a chain line

4. warranty card

5. certificate

2.Specific use steps

1. Select SIM card:

You can use mobile or Unicom’s 2G SIM card, or Unicom 3G card

Supports SMS / GPRS function and has sufficient balance.

2. Remove the four screws from the rear cover, open the rear cover of the device, insert the SIM card into the SIM card slot and lock it.

1.Turn the switch to ON, smart lock boot.

2.Install the SIM and turn on the battery switch, cover the bottom cover, on the good screw

3.unlock

Put the RFID card on the shell RFID tag position, this time the lock electric will turn, when the lock is successful, the buzzer will ring a reminder.

4.lock off

Insert the lock line into the keyhole, when the lock detects the lock line is installed normally, the lock will automatically lock, when the lock after the buzzer will ring a reminder. When the motor lock in the lock when the change, the buzzer will prompt the user long, the lock failed, please re-lock.

5.Set the machine parameters:

After you have read the above description of the product, the product has been installed and the SIM card is installed. The following specific operation to start using.

Note: So the SMS command should be entered in English mode, the command error or format error will not reply.

1.Device IP address and Port

Send the message to the device number on the instruction format：

AS1234*F10#1,113.106.93.50,8011,1#

Reply to terminal parameters

IP:113.106.93.50,8011,1,cmnet,gprs,gprs,ID:31684086,M:6,GPS:A,9,CSQ:19,CGR:5,ACC:1,BAT:65%,VER:AT10-V1.0

Such as：

IP address:113.106.93.50 port:8011，TCP

Order“AS1234*F10#1,113.106.93.50,8011,1#”

The instruction is * AS *, “1234″ is the password, the initial default is 1234, “* F10 # 1″ means that this command is to set the machine’s IP instruction, 113.106.93.50 that the machine is connected to the server, 7001 for the port, 0 means the machine uses UDP to connect with the platform, if you want to use TCP to 1.

2.Query terminal status   

Send SMS to device number, instruction format

AS1234STATE#

Reply terminal parameter

IP:113.106.93.50,8011,1,cmnet,gprs,gprs,ID:31684086,M:6,GPS:A,9,CSQ:19,CGR:5,ACC:1,BAT:65%,VER:AT10-V1.0

IP: 113.106.93.50 Represents the server address reported by the current machine，

Port: 7001 Represents the port of the current machine，0 means UDP Report，If it is 1 means TCP report

Cmnet,gprs,gprs：means current device APN

ID：31684086 means device ID number

GPS:A,9 means the positioning state of the current machine, V means  no positioning，A means,9 mean 9 level accuracy

CSQ:19,Mobile information for the current machine

CGR：5 indicates the status of the card，

ACC：1 indicates the status of the lock, the 1 is the unlock, and the 0 is the lock

BAT：65% current lock capacity

VER: AT10-V1.0 Represents the version that is currently burned by the machine

M:6 That represents the current state of the machine, 6 online, 0 said 1 initialization, query CSQ, 2 registered network, 3 query the status of the CGREG, said the 4 registered APN, 5 said the connection to the server, 7 is disconnected from the network, said the 8 call, said 9 upgrade

3.SMS unlock 

Send SMS commands “AS1234*F10#8,888888, #” to the number of terminal equipment, the contents of the “Open lock OK replied,” to this content said off terminal unlock success

The password can be unlocked remotely. For security, please consult the supplier to unlock the password.

4.Set the unlock reporting frequency 

Send SMS instructions“AS1234*F10#G,300,600,#”Number to device，The terminal replies to

“accOn:300 accOff:600 rd:0 sp:0,0s stp:0 dr:0,0 idl:0 mv:0 time:+8 cq:0,0 geo:0 step:377 ack:0 msg:2568,56 sleep:0,0

”，The terminal has returned this content to indicate successful recovery

ACCon:Represents the lock off reporting interval

ACCoff:Represents the lock on reporting interval

Sleep Represents sleep time

5.Restore factory   

Send SMS instructions“ASAX*%UPAS”Number to device，The terminal replies to“password:1234,OK”，The terminal has returned this content to indicate successful recovery

6.Restart terminal   

Send SMS instructions“AS1234RSGS#”To the number of the device, the terminal replies to“GSM/Restart;OK”，The terminal has returned this content to indicate a successful restart

Attention：

• All the SMS edit in English mode, Chinese mode input will lead directly to delete, do not reply sms.
• All the messages are beginning to AS, to the end of #, format error will cause the application to not recognize.
• The 1234 machine factory default password, if the password is wrong, will cause the application to not reply SMS

3.location monitoring

When using a computer or mobile phone to monitor the terminal, the mobile phone or computer is required to access the Intel Network normally.

Enter in the IE browser’s address bar: https://bs.flyinggnss.net/, as shown in the following figure:  test account : lqtest   pass code: 123456

Enter the account password and enter the monitoring platform. As shown in the following figure:

1， Basic operation：

1） Inquiring vehicle，

in the monitoring platform, point monitoring center, into the monitoring interface, click on the list, click the license plate click on designated vehicles, that can query the platform to the location of the vehicle

Corresponding positioning information will appear on the map. As shown in the following figure

On the map can display the lock position, unlock state, power, unlock number and other information.

According to the tips behind the vehicle, you can see whether the vehicle is on the line. As shown in the following figure:

b.Click the query in the map monitor bar，

In the content box, enter the fuzzy information, in the list below, you can display the input information relating to the vehicle. Click on the vehicle you need to query to display the corresponding text and map vehicle information on the right. As shown:

(Note: the addresses on the corresponding map are displayed, and the last location is the location information displayed.)

2） Give instructions to designated vehicles：

a.Order to unlock

Select the vehicle you want to operate, and have a more choice on the right side of the car，

More points into the selection of the next instruction, select the unlock item, you will ask for input authentication password, test password default 888888, in use, please modify the password, and do not leak.

Enter the password after the point unlock, the terminal received the terminal will answer the unlock successfully, on the platform will show unlock.

Main user interface :

Folloing ing are details :

1.More instructions

2.Open lock remotely

3.Set the lock interval time

4.History Route Playback :

5.Choose time and comfirm OK

6.Geo-fence

7.Online tracking:

8.Find and check fleetmanagement data