Competitive Price for Vehicle Manager Fleet - cheap gps tracker Long Connection GPS Tracker MT009 – Dragon Bridge

 GPS vehicle communication terminal

(GPS+GSM+SMS/GPRS)

1.Product accessories

Power 4P line 1 (standard)

Fast installation and use guide 1 copies (standard)

Velcro

2.product function

2.1 GSM850/900/1800/1900MHZ four frequency system;

2.2 ultra wide operating voltage input range: 12-100vDC;

2.3 GPS continuous positioning, GPRS timing report;

2.4 support SMS SMS query location information;

2.5 built in vibration sensors to achieve intelligent vehicle anti-theft;

2.6 ACC ignition signal detection, vehicle status prompt;

2.7 can be connected to the oil and electricity relay, remote control of vehicles; (optional)

2.8 built in standby battery to realize illegal line cutting alarm

3.product specifications

3.Installation instructions

3.1 preparation before installation

3.1.1 open the packing box, check the equipment model is correct, accessories are complete, otherwise please contact your dealer;

3.1.2 device terminal needs to insert a GSM SIM card to work properly. GSM card can be connected or moved optionally (GSM network is global). Please prepare a valid SIM card.

Be careful：

1. before installing or taking out the SIM card, please switch the power switch on the side of the terminal to the shutdown position;
2. whether the terminal SIM card has GPRS function;
3. the terminal SIM card needs to open the caller ID function (according to the function of the customer’s choice to open or not to open);
4. make sure that the terminal SIM card is used properly

3.2 select installation location

The installation mode of terminal is suggested to be concealed installation. The hidden installation of terminal equipment should be installed by the professional agency designated by the dealer, and pay attention to the following matters:

3.2.1 in order to avoid thieves damage, equipment selection should be concealed as far as possible;

3.2.2 avoids putting together with emission sources, such as reversing radar, burglar alarm and other vehicle mounted communication equipment;

3.2.3 can be fixed with tie tape or with double adhesive with wide sponge;

3.2.4 equipment is equipped with GSM antenna and GPRS antenna, installation should ensure that the receiving face up (air empty), and no metal shielding above, recommended installation position:       

1. The front windshield below the decoration box cover;
2. Before the instrument panel (epidermal non-metallic material) around the shelter;
3. The rear windshield trim down below.

3.2.5 If there is a metal insulation layer or heating layer on the windshield of the car, it will reduce the GPS receiving signal and cause GPS malfunction. Please change the installation position of the equipment.

4. Matters needing attention in equipment wiring

4.1 power supply, ACC, oil and electricity control line (4Pin)

4.1.1 the equipment standard power supply for 12V-100VDC power line, please use the original offer, the red line for the positive power supply, black for the cathode of the power supply; please choose the cathode of the power supply grounding alone or ground installation, not with other ground together;

4.1.2 equipment orange line to the ACC line, be sure to pick the ACC vehicle terminal will switch, according to the ACC state to determine whether to enter the fortification; if no ACC line will allow vehicles to enter the default fortification state, vehicle vibration occurs, will trigger a vibration alarm. If the anti-theft function is not needed, the ACC line can be directly connected with the positive pole of the power supply.

4.1.3 break the oil and electricity control line (yellow line) to connect the yellow line on the relay.

5. Short message instructions and methods of use: all instructions must be input in English status

Send SMS code with mobile phone to GPS vehicle communication terminal SIM card number, separated symbol is comma. The comma in the following short message instruction format is English input state format, the letters are not written by the instruction, and the comma is input in English state.

5.1 basic operation settings

5.1.1 center number settings (that is, the owner number must be done, otherwise it can not do other operations):

5.1.2 settings center number: you must use the owner number to send SMS to the terminal SIM card number

SMS format: admin123456 158********

The “155********” is the number of mobile phone SIM card which needs to be bound. After receiving the message that the center number is set successfully, the owner can perform other short message instructions on the terminal or check the car on the internet.

  5.1.3 modify the terminal password: please remember the password, such as forget the owner’s center number can be sent to restore the factory settings instructions

The default terminal password is: 123456

Modify the terminal password instruction: pwd123456 666888 (666888 is a new password, must be six digits)

Reply message: password modification successful, new password: 666888, please be careful to keep!

5.2 anti-theft alarm location query settings

Chinese location query in 5.2.1:

The center number sends instructions to the SIM card of the terminal device, and the terminal replies the last Chinese position information to the central number.

Instruction format: DW or 123

Reply information: Shenzhen city of Guangdong Province, Longgang District, Cloth Dragon Road, Bantian Metro (Shenzhen) 12 meters southeast

6. Garrison fortification:

6.1 defense instruction format: SF     reply message: SF OK

6.2 instruction format: CF             reply message: CF OK

7. Vibration alarm：

 When the automobile flameout tube enters the automatic fortification, the continuous vibration for more than 3 seconds will trigger the vibration alarm.

7.1.2 open vibration SMS alarm: 125# (default)

Reply SMS: OK

7.1.3 closed vibration SMS alarm: 126#

Reply SMS: OK

7.1.4 open vibration alarm: 122#

Reply SMS: OK

7.1.5 turn off the vibration phone alarm: 121# (default)

Reply SMS: OK

7.1.6 set vibration alarm duration SMS instructions, 1-15 seconds.

Instruction: vibtime123456, n reply: vibtime set OK

N (0~15), 0 cancel vibration alarm, default 3 seconds, that is, vibration lasts 3 seconds alarm

7.2 shift alarm:

7.2.1 shift alarm setting instruction: move123456 300 (default) unit: meter reply: move OK

7.2.2 closed instruction format: move0

SMS: displacement alarm: closed

7.3 overspeed alarm:

7.3.1 overspeed SMS alarm speed limit: speed123456 080 set speed limit of 80 km / h.

7.3.2 shut down speeding SMS Notifications: speed123456 000 (default) reply: speed OK

7.3.3 speeding SMS notification: speed123456 080 reply: speed OK reply SMS: overspeed alarm: 80 km / h

8. Open oil cut off

When the vehicle theft occurs, the monitor can send out the oil and electricity instructions initiatively, and cut off the oil circuit of the stolen vehicle under the premise that the vehicle is in safe driving, so that the vehicle can not be started.

Note: to ensure the safety of vehicles, only in the GPS terminal in the effective positioning state, and to meet the vehicle speed is less than 20KM/H under the condition when the vehicle is stationary or interruption oil electric operation.

When the robbery alarm is released, the oil and electricity instructions are manually sent back by the monitoring background, and the terminal performs the oil and electricity recovery operation, and the vehicle can continue to run.

SMS break oil: DY

SMS open oil: KY

9. Device recovery query settings

9.1.2 restore factory settings instruction format: format

Reply SMS: alarm will immediately restore the factory settings, all previous settings will be canceled.

9.1.3 restart instruction format: CQGPS

9.1.4 query device information:

Instruction format: CXZT

Reply information: version, ID, IP, port, domain name, APN

10. Global positioning service platform

Users can log in the global positioning service platform provided by the dealer to check the location and status of the vehicle, and the corresponding operation, the service platform web site, please consult your dealer.

Platform operation：

1.In the use of mobile phone market search:www.dbgps.com 

Click on the top right of the IMEI landing, the first box corresponding to the input box to enter the platform site, second behind IMEI, third frame platform input password (default 123456), click on the log in information (don’t remember again, and then click on the input) landing, as shown in Fig.

2.website platform:

 open the website www.dbgps.com, select IMEI/ license plate number user type. Enter the IMEI number at the back of the device, and then enter the password (default 123456, as shown in Fig.