2G MT-008 wired GPS tracker
- Network: 2G
- Support: RS232 , RS485 ,Optional 4 way temperature or humidity
4G MT-008 wired GPS tracker
- Network: 2G
- Support: RS232 , RS485 ,Optional 4 way temperature or humidity
MT-008 is a Highly Integrated Car Terminal, that supports a 4-way temperature sensor refrigerator. The host of this terminal is a low-power wireless transmitter and receiver. It receives and sends radio frequency signals during use. MT-008 supports RS485 or RS232 or CAN interface.
1. Data transmission: This product supports 2G (GSM) / 3G / 4G / NB mobile network
2. Positioning: Use a high-sensitivity GPS / BD module to obtain position information more accurately;
3. SOS alarm: One-button emergency alarm (requires optional SOS button);
4. communication interface: external temperature sensor, tire pressure, fuel consumption sensor, CAN BUS bus;
5. Taking pictures: The external camera of the terminal can realize remote taking pictures;
6. analog detection: the terminal supports detection of analog signals, such as voltage;
7. Low output: The terminal supports two low-output signals, which can be used to drive oil cut off, alarm, etc .;
8. Under-voltage alarm function: When the vehicle battery voltage is too low, the terminal will generate a battery under voltage alarm to the platform;
9. Power failure alarm function: When the external power supply of the terminal is disconnected, the terminal will generate a power failure alarm to the platform;
10. Remote upgrade: remote terminal software can be updated;
11. Remote query and setting parameters: remote setting, query parameters and location query via SMS, platform;
12. Blind zone supplementary transmission: When the vehicle is driving to no mobile network signal or network, the terminal will store the position information at this time.
Come, wait for mobile network recovery to send to the server immediately, up to a million storage;
13. Electronic fence: The terminal support service platform sets up an electronic fence, which needs server platform support;
14. Speeding alarm: When the vehicle speeds over the preset limit when the vehicle is driving, the terminal will generate an over-speed alarm and upload it to the location server
15. Remote oil and power-off: The terminal supports remote oil and power-off function;
16. Remote restart: The terminal supports the remote restart function;
17. Custom input and output: The terminal has a maximum of 4 custom inputs and 2 custom outputs, which can be configured accordingly as required;
18. Collision alarm: the built-in sensor can detect the collision of the vehicle;
19. Mileage statistics: The terminal can accurately count the mileage of the terminal after it is installed on the vehicle;
20. Support RS485 or RS232 or CAN interface.
|
Identification |
Wiring color |
Features |
|
|
1 |
BAT |
red |
Power supply positive terminal, connected to car battery positive terminal |
|
2 |
GND |
black |
Negative power supply, connect to the negative battery of car or ground |
|
3 |
ACC |
Orange |
ACC high detection (optional speed detection) |
|
4 |
5V |
Fine red |
5V output / high input 1 |
|
5 |
TX |
green |
RS232 TX / RS485-A / CAN + / low output 1 |
|
6 |
RX |
yellow |
RS232 RX / RS485-B / CAN- / low output 2 |
|
7 |
GND |
black |
Negative power supply, connect to car battery negative or ground, depending on the actual situation |
|
Identification |
Wiring color |
Features |
|
|
1 |
BAT |
red |
Power supply positive terminal, connected to car battery positive terminal |
|
2 |
GND |
black |
Negative power supply, connect to the negative battery of car or ground |
|
3 |
ACC |
Orange |
ACC high detection (optional speed detection) |
|
4 |
5V |
Fine red |
5V output / high input 1 |
|
5 |
TX |
green |
RS232 TX / RS485-A / CAN + / low output 1 |
|
6 |
RX |
yellow |
RS232 RX / RS485-B / CAN- / low output 2 |
|
7 |
GND |
black |
Negative power supply, connect to car battery negative or ground, depending on the actual situation |
Fault resolution
|
Failure phenomenon |
fault resolution |
| The terminal has been unable to connect to the background server after the first installation, and the background display is not online | Whether the main power wiring is correct, take care not to connect it to the car's internal control line; |
| Whether the SIM card is correctly installed; | |
| Check parameter settings; | |
| Check whether the identity information of the terminal is correctly entered on the platform; | |
| Whether the ACC line is connected, insert the car key and connect to ACC ON; | |
| Check whether it has been located. If it is not located, go to the outdoor open area for the first time; | |
|
Terminal shows offline status in background |
Dial the SIM card number of the device to see if you can hear the phone connection; |
| Whether the SIM card is in arrears and whether the GPRS data service is cancelled; | |
| Whether the vehicle has no GSM network signal coverage in the basement; | |
| Observe whether the offline area is offline or all offline, and determine whether it is a network problem of the operator; | |
|
The terminal is not positioned for a long time or the positioning deviation is large |
Whether the front installation is correct, facing up to the sky; |
| Whether there is a substance (such as metal) that absorbs electromagnetic waves above the front installation location, and whether there is an explosion-proof thermal insulation film on the glass above the location (the higher metal content in the film will absorb high-frequency electromagnetic waves); | |
| Observe whether there are tall buildings obstructing satellite positioning signals in the surroundings, avoid metal shields and stay away from high-power signal sources. Please drive to a more open place for positioning. Generally, the first positioning time takes 1-2 minutes;When the p | |
| When the positioning is inaccurate, please pay attention to check whether the LED is positioned. If it is not positioned, it is the historical position point or LBS position. When the positioning indicator is always on and inaccurate, please check whether the turnover environment has a unidirectional or Y-plane signal reflecting the building. | |
|
LED is off after power on |
Please check whether the car battery voltage is normal; |
| Whether the main power wiring is correct, take care not to connect it to the car's internal control line; | |
| Please check whether the fuse of the main power wiring is blown; |
1.Green LED, network indication
|
Indication status |
LED status |
|
Search network |
Fast blinking, 0.5 on, 0.5 second off |
|
Already registered on the network |
On for 0.5 seconds and off for 1 second |
|
Connect to server |
Always on |
2.Blue LED, GPS positioning indication
|
Indication status |
LED status |
|
Not targeted |
Fast blinking, 0.5 on, 0.5 seconds off |
|
Targeted |
Always on |
